Core Process in Metadata Publishing

Core process in metadata publishing

Core Process in Metadata Publishing 1

The following are some of the core processes in metadata publishing Gathering of metadata requirements Selection of metadata registry and metadata publishing tools Training of metadata concepts to project participants Stakeholder group formation Metadata harvesting Glossary consolidation Initial upper ontology construction (abstract data elements) Draft data element loading Data element review process Publishing approved metadata elements in a variety of output formats (see below) Creation and maintenance of versions and depreciation of unused or redundant data elements

— — — — — —

Core business

Since Schottel developed the first Z-drive in the 1950s the product portfolio has been extended by a range of thruster types (selection). The Schottel RudderpropellerThe idea of the rudderpropeller was the result of Becker's thoughts about the propulsion plants that took up too much space on board. He was looking for a system that could be installed space-efficiently with good maneuvering properties and developed a Z-drive system with a propeller that could be endlessly steered through 360 degrees. A classic application for rudderpropellers is tugs as the example of Janus shows. The first tractor tug was commissioned in 1967 in the Port of Hamburg. It was equipped with two Schottel Rudderpropellers in the front third of the vessel. The Schottel Rudderpropeller is used in almost any kind of vessel from offshore vessels to tugs. It is available as a fixed pitch or controllable-pitch propeller. It is also available as a hydraulically retractable system for open-water service, dynamic positioning or varying water depths and underwater mountable thruster for ships that need to reduce docking times. In 2014 Schottel introduced a rudderpropeller with an additional electric motor (PTI - power take in)[clarification needed] as a hybrid propulsion concept. Here, the electric motor suffices for partial-load duties, the diesel engine is employed for operation at greater load, and the electric motor can be switched on to provide additional power. The PTI and diesel engine are centrally-controlled as a single system. This thruster is installed in the tug Eddy, built by Holland Shipyard. The Schottel Twin PropellerThe demand for increasing power ratings could first be answered with larger rudderpropellers. Limits were set to this trend by mechanical stress and the fact that with an increasing propeller diameter, the draft of the vessel inevitably increases. Schottel therefore developed a thruster where the required power is divided between two counter-rotating thrusters that share a single shaft. The Twin Propeller is equipped with a pull propeller and a push propeller. The vortex street of the front pull propeller passes between the blades of the rear push propeller without impeding it. Contraction of the slip stream in the pull propeller means that more water reaches the push propeller from the sides. The strut is equipped with a fin, thus the swirl energy generated in the propeller stream is recovered. Additionally, the flow around the fins creates a lift component in the thrust direction, which has a thrust-enhancing effect. The Schottel Combi DriveThe Combi Drive is based on the Schottel Rudderpropeller and combines its characteristics with the principle of an electric drive. The Combi Drive exists in both single and twin propeller versions. Instead of an above-water gearbox, the electric motor is integrated into the vertical shaft of the thruster. In combination with a power management system, electric drives increase the efficiency of the propulsion system and reduce fuel consumption. Electric energy generation systems produce only the power currently required and distribute it to the various consumers. The Schottel Pump JetSchottel developed the Pump Jet for shallow waters. It is also used as an additional maneuvering aid for main propulsion or as a redundant auxiliary propulsion unit. An impeller sucks in water from under the hull and forces it into a pump housing. The outlet nozzles are integrated into an azimuthing base plate which is installed flush with the hull. The Schottel Controllable Pitch PropellerSchottel Controllable Pitch Propellers can be used in several vessel types like bigger ferries, container ships, heavy lift vessels or offshore supply vessels. The power spectrum includes application up to 30 MW (40,000 hp). The propeller diameters vary between 1.5 and 8.0 metres (4 ft 11 in and 26 ft 3 in). Unlike a conventional fixed pitch propeller, the blades can be rotated and change their pitches variably from zero thrust to headway or reversing. The Schottel Transverse ThrusterTransverse Thrusters are installed in the bow or stern of a vessel in order to improve maneuverability. Depending on the type of vessel, the range of application for Transverse Thrusters extends from harbor maneuvering to positioning tasks offshore. The units can be installed either with a horizontal or vertical motor flange.

the core Статьи по Теме
Multi Channel Laser Anti-theft Alarm Circuit
How Do I Make My Go Kart Faster, Without Spending too Much Or Nothing?!?
What Solute Will Be Replaced by Liquid Electrolyte in Commercial Lithium Ion Battery?
Pool Stage
Introduction of Tubular Soil Moisture Monitoring Station

Copyright © 2020 Concises YuGa Sports | Sitemap